Service Source K Upgrades Power Macintosh 7200 Series/WS 7250
Upgrades 7” PC CARD - 9 7 Swing open the chassis to provide access to the logic board.8 Flip down the chassis support arm. Be sure the support arm e
Upgrades 7” PC CARD - 10 9 Insert the small end of the PC audio/video cable assembly into the socket on the corner of the PC Compatibility Card. (Yo
Upgrades 7” PC CARD - 11 10 Insert the card into the slot whose blank PCI slot cover you removed earlier. Press down firmly on the card until the co
Upgrades 7” PC CARD - 12 11 Plug the large end of the internal PC audio/video connector into the socket on the logic board.Internal PC Audio/Video C
Upgrades 7” PC CARD - 13 12 Disconnect the CD audio cable from the Sound In connector on the logic board.
Upgrades 7” PC CARD - 14 13 Pull the cable through the hole in the chassis and set it aside.
Upgrades 7” PC CARD - 15 14 Plug one of the CD audio cables that came with the PC Compatibility Card into the Sound Out connector on the PC Compatib
Upgrades 7” PC CARD - 16 15 Route the cable over the top of the card and along the back edge of the computer’s logic board. Note : Keep the cable aw
Upgrades 7” PC CARD - 17 17 Connect the second CD audio cable to the CD In connector on the PC Compatibility card. Note: The CD In connector is in
Upgrades 7” PC CARD - 18 18 Route the second cable over the top of the card, along the back edge of the logic board, and through the hole in the com
Upgrades 7” PC CARD - 1 7” PC CARD The 7” PC Compatibility Card Upgrade kit includes the PC Compatibility card, a loopback cable, an internal PC a
Upgrades 7” PC CARD - 19 19 Disengage the support arm from the hole in the chassis bottom, and close the computer’s upper chassis. Note: Make sure
Upgrades 7” PC CARD - 20 20 Lock the chassis latches.Chassis Latches
Upgrades 7” PC CARD - 21 21 Replace the support foot.Support Foot
Upgrades 7” PC CARD - 22 22 Reconnect the auxiliary fan (if present) to the logic board.Auxiliary FanAuxiliary Fan Connector
Upgrades 7” PC CARD - 23 23 Flip the expansion card cover up and snap it back into place. (Be sure to snap the cover back down on both ends.) Note:
Upgrades 7” PC CARD - 24 24 Connect the CD-ROM cable you threaded through the computer’s chassis earlier to the Audio connector on the CD-ROM drive.
Upgrades 7” PC CARD - 25 25 Make sure all cables and cards are firmly connected.26 Replace the top housing. (Refer to the Take Apart chapter for ins
Upgrades 7” PC CARD - 26 Connecting Monitors After you have installed the 7" PC Compatibility Card, connect the monitor(s) as follows to displa
Upgrades 7” PC CARD - 27 To connect a single monitor to the computer: 1 Connect the monitor cable to the computer’s built-in video port.Video Port
Upgrades 7” PC CARD - 28 To connect a single monitor to the computer using a video card: 1 Attach the short connector on the loopback cable to the m
Upgrades 7” PC CARD - 2 Note : The PC Compatibility card offers two ways to get video out on the Power Macintosh 7200: 1)via the internal PC audio/v
Upgrades 7” PC CARD - 29 To connect two monitors to the computer: 1 Connect the monitor you want to use for the Mac OS environment to the video port
Upgrades 7” PC CARD - 30 4 In most cases, leave the long connector on the loopback cable unplugged. But if the computer has an additional video port
Upgrades 12” PC CARD - 31 12” PC CARD The 12” PC Compatibility Card Upgrade kit includes the PC compatibility card, a loopback cable, an internal PC
Upgrades 12” PC CARD - 32 Note : The PC Compatibility card offers two ways to get video out on the Power Macintosh 7200: 1)via the internal PC audio
Upgrades 12” PC CARD - 33 1 Disconnect the CD audio cable from the CD-ROM drive.(Top, Back of Computer)CD AudioCable
Upgrades 12” PC CARD - 34 2 Flip open the expansion card cover.(Front of Computer)ExpansionCard Cover
Upgrades 12” PC CARD - 35 3 Disconnect the auxiliary fan cable (if present).Auxiliary Fan ConnectorAuxiliary Fan
Upgrades 12” PC CARD - 36 4 Remove the first blank PCI slot cover. Note : It is recommended that you install the PC Compatibility Card in the first
Upgrades 12” PC CARD - 37 5 Flip open the chassis support foot.Support Foot(Front of Computer)
Upgrades 12” PC CARD - 38 6 Release the chassis latches.Chassis Latches
Upgrades 7” PC CARD - 3 Before you begin, remove the top housing.1 Disconnect the CD audio cable from the CD-ROM drive.(Top, Back of Computer)CD Aud
Upgrades 12” PC CARD - 39 7 Swing open the chassis to provide access to the logic board.8 Flip down the chassis support arm. Be sure the support arm
Upgrades 12” PC CARD - 40 9 Insert the small end of the PC audio/video cable assembly into the socket on the corner of the PC Compatibility Card. (Y
Upgrades 12” PC CARD - 41 10 Insert the card into the slot whose blank PCI slot cover you removed earlier, making sure that the end of the card fits
Upgrades 12” PC CARD - 42 12 Plug the large end of the internal PC audio/video connector into the socket on the logic board.Internal PC Audio/Video
Upgrades 12” PC CARD - 43 13 Disconnect the CD audio cable from the Sound In connector on the logic board.
Upgrades 12” PC CARD - 44 14 Pull the cable through the hole in the chassis and set it aside.
Upgrades 12” PC CARD - 45 15 Plug one of the CD audio cables that came with the PC Compatibility Card into the Sound Out connector on the PC Compati
Upgrades 12” PC CARD - 46 16 Route the cable over the top of the card and along the back edge of the computer’s logic board. Note : Keep the cable a
Upgrades 12” PC CARD - 47 18 Connect the second CD audio cable to the CD In connector on the PC Compatibility card. Note: The CD In connector is i
Upgrades 12” PC CARD - 48 19 Route the second cable over the top of the card, along the back edge of the logic board, and through the hole in the co
Upgrades 7” PC CARD - 4 2 Flip open the expansion card cover.(Front of Computer)ExpansionCard Cover
Upgrades 12” PC CARD - 49 20 Disengage the support arm from the hole in the chassis bottom, and close the computer’s upper chassis. Note: Make sure
Upgrades 12” PC CARD - 50 21 Lock the chassis latches.Chassis Latches
Upgrades 12” PC CARD - 51 22 Replace the support foot.Support Foot
Upgrades 12” PC CARD - 52 23 Reconnect the auxiliary fan (if present) to the logic board.Auxiliary Fan(Side View)Auxiliary Fan Connector
Upgrades 12” PC CARD - 53 24 Flip the expansion card cover up and snap it back into place. (Be sure to snap the cover back down on both ends.) Note:
Upgrades 12” PC CARD - 54 25 Connect the CD-ROM cable you threaded through the computer’s chassis earlier to the Audio connector on the CD-ROM drive
Upgrades 12” PC CARD - 55 26 Make sure all cables and cards are firmly connected.27 Replace the top housing. (Refer to the Take Apart chapter for in
Upgrades 12” PC CARD - 56 Connecting Monitors After you have installed the 12" PC Compatibility Card, connect the monitor(s) as follows to disp
Upgrades 12” PC CARD - 57To connect a single monitor to the computer:1 Connect the monitor cable to the computer’s built-in video port.Video Port
Upgrades 12” PC CARD - 58To connect a single monitor to the computer using a video card:1 Attach the short connector on the loopback cable to the mon
Upgrades 7” PC CARD - 5 3 Disconnect the auxiliary fan cable (if present).Auxiliary Fan ConnectorAuxiliary Fan
Upgrades 12” PC CARD - 59To connect two monitors to the computer:1 Connect the monitor you want to use for the Mac OS environment to the video port o
Upgrades 12” PC CARD - 604 In most cases, leave the long connector on the loopback cable unplugged. But if the computer has an additional video card
Upgrades Power Macintosh 7600 Upgrade - 61Power Macintosh 7600 UpgradeThe Power Macintosh 7600 Upgrade kit includes:• A Power Macintosh 7600 logic bo
Upgrades Power Macintosh 7600 Upgrade - 62Before you begin, remove the following components. Refer to the Take Apart chapter in this manual for instr
Upgrades Power Macintosh 7600 Upgrade - 631 Remove the Power Macintosh 7200 logic board. (Refer to the Take Apart chapter for instructions.)IMPORTANT
Upgrades Power Macintosh 7600 Upgrade - 642 Install the EMI gasket between the sound in and sound out ports on the Power Macintosh 7600 logic board.N
Upgrades Power Macintosh 7600 Upgrade - 653 Install the EMI clip that came with the Upgrade Kit onto the Power Macintosh 7600 logic board in the same
Upgrades Power Macintosh 7600 Upgrade - 66Note: For the next two steps, turn the computer so you are facing the inside of the rear panel.6 Press in o
Upgrades Power Macintosh 7600 Upgrade - 677 Place the video out cover over the bottom two openings on the left side.
Upgrades Power Macintosh 7600 Upgrade - 688 From the inside of the computer, position the AV module into the plastic frame so that its connectors fit
Upgrades 7” PC CARD - 6 4 Remove the first blank PCI slot cover. Note : It is recommended that you install the PC Compatibility Card in the first sl
Upgrades Power Macintosh 7600 Upgrade - 69Note: At this point you must install a processor card in the computer. The processor card is not included i
Upgrades Power Macintosh 7600 Upgrade - 7011 Position the card evenly over the processor card slot and press down gently. Do not force the card or yo
Upgrades Power Macintosh 7600 Upgrade - 7112 If you are installing a 132 MHz card, be sure to install the EMI grounding clip that came with the 132 M
Upgrades Power Macintosh 7600 Upgrade - 7213 Replace the following components. Refer to the Take Apart chapter for instructions:• Power Actuator• Spe
Upgrades 7” PC CARD - 7 5 Flip open the chassis support foot.Support Foot(Front of Computer)
Upgrades 7” PC CARD - 8 6 Release the chassis latches.Chassis Latches
Kommentare zu diesen Handbüchern