Apple Processor Cage and Clips Installationsanleitung Seite 50
- Seite / 117
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
7 Cabling the Storage System
For more information about cabling drive enclosures (SAS) before you continue to cable the system,
visit www.hp.com/go/3par. Scroll to Support, and click HP 3PAR StoreServ 7000 Support and
then Manuals. Then scroll to Setup and install — general and select the specific HP 3PAR StoreServ
7000 Storage Cabling Configuration Guide.
Cabling Controller Nodes
Nodes are numbered 0 to 3 from bottom to top. Connections between Nodes 0 and 1 and Nodes
2 and 3 use four large interconnect cables.
These cables are directional and must be installed correctly for the storage system to function
properly. When inserting the cables, you should hear a click to confirm the cable is correctly
installed. If you have to force the connector, the connector is upside down and needs to be inverted.
The direction of the cable connection is indicated by labels on either end of the cable.
In Figure 33 (page 50), see label A for interconnecting node 0 or 1. See label C for interconnecting
node 2 or 3.
Figure 33 Interconnecting the Controller Nodes
C
A
Host/Ethernet Cables
WARNING! Each controller node supports one Ethernet connection to a switch or hub. Separate
connections from the Ethernet switch or hub to at least two controller nodes are required to support
redundancy. With redundancy, one IP address is shared between the two connections, and only
one network connection is active at a time. If the active network connection fails, the IP address is
automatically moved to the surviving network connection.
WARNING! At a minimum, the storage system requires one Fibre Channel (or iSCSI) connection
from a host computer to a controller node. HP recommends separate connections from each host
computer to each of the controller nodes in the storage system, with connections distributed evenly
across all nodes.
50 Cabling the Storage System
- Storage Installation Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 1 General Site Planning 6
- Acclimatization 8
- 2 Getting Started 9
- Inspecting the Packaging 10
- Storage System Installation 11
- Disk Drive Numbering 12
- Controller Nodes 13
- I/O Modules 17
- Power Cooling Modules 17
- Service Processor 19
- Power Distribution Units 19
- Important Safety Information 20
- Required Tools 21
- Additional requirements 21
- Configurations 21
- • 1U and 0U configurations 22
- Hardware Installation 23
- Hardware Installation 25 25
- Installing the 1U and 0U PDUs 27
- • 0U bracket installation 28
- 3. Install cage nuts 28
- Securing the Cables 29
- Installation is complete 30
- Unpacking the Cabinet 31
- Positioning the Cabinet 31
- Verify the Cabling 32
- Removing the Brackets 34
- Installing the Rail Kit 35
- Installing the Rail Kit 37 37
- Installing Enclosures 38
- (LFF) disk drive) 40
- Installing a Disk Drive 41
- NoneRound hole 43
- NoneSquare hole 43
- ScrewdriverThreaded hole 43
- • Screwdriver 44
- 7 Cabling the Storage System 50
- Cabling Expansion Cabinets 51
- Cabling the Service Processor 52
- Cabling the Power Strips 53
- Verifying Setup 54
- Verifying LED Status 56
- Figure 37 Disk Drive LEDs 57
- Table 9 PCM LED Descriptions 58
- Node Interconnect Ports 60
- Drive Enclosure LEDs 61
- Figure 42 Front Panel LEDs 62
- Table 11 Front panel LEDs 62
- Figure 43 Rear Panel LEDs 63
- Table 12 Rear panel LEDs 63
- Prerequisites for Using a VSP 64
- Deploying the VSP OVF File 65
- Launching HP 3PAR SmartStart 72
- Generate Service Processor ID 75
- Configure SP Networking 76
- Remote Support 77
- System Support Information 79
- Time and Region 80
- Change Passwords 81
- Applying Settings 83
- Figure 57 Apply Settings 84
- Verify Storage System 88
- Configure Networking 89
- ◦ Subnet Mask 89
- ◦ Gateway 89
- Configuring Time 89
- Figure 65 Configure Time Page 90
- Change Password 91
- Verify Configuration 92
- Progress 92
- Figure 68 Progress Page 93
- Figure 69 Results Page 93
- Contacting HP 95
- HP 3PAR documentation 95
- Typographic conventions 98
- HP 3PAR branding information 98
- 12 Documentation feedback 99
- Figure 74 7000 Series PCM 101
- Figure 75 M6700 Series PCM 102
- Figure 77 SFF Drive Assembly 102
- Figure 79 LFF Drive Assembly 103
- Accessory Kits 104
- Rail Kits 104
- Rail Kits 105 105
- Figure 87 M5 Cage Nut 106
- Adding Disk Drives 110
- Checking Progress 111
- Completing the Upgrade 112
- SmartStart is Unavailable 113
- E Validating Remote Support 114
- G Troubleshooting 117
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern